Wheelock MT4-12-LS Anleitung zur Fehlerbehebung PDF herunterladen (Seite 37)

– 37 –

4. For selection of the next word (e.g., DOOR), repeat step 3, as follows.

Press key [3] until the first letter of the next word appears (e.g., "D"). Then

press [6] to display the first available word beginning with that letter (e.g.

DAUGHTERS). Press [3] repeatedly until the desired word (e.g., DOOR)

appears. To accept the word, press [6], which toggles back to the alphabet

list.

5. When all desired words have been entered, press [8] to store the description

in memory.

6. Enter

NN, where NN is the next zone that you want to review or for which

you want to program a descriptor. To modify the descriptor, enter

again. To exit this mode, press “

00”.

Adding Custom Words

You can add up to five installer-defined words to the built-in vocabulary. Each

of the five "words" can actually consist of a "word string" of one or more words,

but no more than ten characters can be used for each word or word string.

Custom words must begin with an alphabetic character. If a

number or symbol is used as the first character, the word will not

be saved.

When adding Custom

Words in steps 3–6, the

keypad keys perform the

following functions:

[3] Advances through the al-

phabet in ascending or-

der.

[1] Moves through the

alphabet in descending

order.

[6] Selects desired letter;

moves cursor one space to

right.

[4] Moves cursor one space to

left.

[7] Inserts a space at the

cursor location, erasing

any character located

there.

[8] Saves the new word in

the system's memory.

1. Perform steps 1, 2, and 3 of Programming the Descriptors on a previous

page.

Select CUSTOM WORD mode (enter “1”) when the prompt CUSTOM

WORD ? is displayed.

2. Enter the number ([1]–[5]) of the custom word or word string to be created

(for example, if you are creating the first custom word or word-string, enter

[1], for the second, enter [2], etc.). A cursor will now appear at the be-

ginning of the second line.

3. One of two methods of entering the custom word's characters can

now be used (refer to the CHARACTER LIST of letters, numbers, and

symbols on a following page):

Method 1:

Press the [#] key, followed by the two-digit entry for the first letter you

would like to display (e.g., [6][5] for "A"), or...

Method 2:

Use the [3] key to advance through the list of symbols, numbers, and

letters. Use the [1] key to move back through the list.

4. When you have reached the desired character, press [6] to select it. The

cursor will then move to the right, in position for the next character.

5. Repeat steps 3 and 4 to create the desired word(s). Note that the [4] key

can be used to move the cursor to the left, if necessary, and that key [7] can

be used to enter a blank (or erase an existing character). Remember, no

word or word-string can exceed 10 characters.

6. Press the [8] key to save the custom word(s) and return to the "CUSTOM

WORD ?" display.

Repeat steps 2–5 for other custom words to be entered. To change a custom

word, just overwrite it. If no more are to be entered now, press [0] to return

to the Descriptor entry. The custom word(s) will be automatically added to

the built-in vocabulary.

When zone descriptors are being entered as described in step 6 of

Programming the Descriptors, the custom word numbers are 250 to 254 for

words 1 to 5 respectively.

When being entered as described in step 3 in Alternate Method For

Programming Zone Descriptors, each word will be found at the end of the

group of words that begin with the same letter as it does.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 75 76

Kommentare zu diesen Handbüchern

Keine Kommentare

Wheelock MT4-12-LS Anleitung zur Fehlerbehebung Seite 37

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Rauchmelder Wheelock MT4-12-LS